Ningbo Kingvos Electrical Appliance Co.,Ltd
Model No.: KV-JQ10001
Packaging: Double Bliter Sealed
Productivity: 30000pcs Per Day
Place of Origin: China
Supply Ability: 400,000pcs per Month
60-100W Hot Melt Hand Gun Features:
100% Brand New.
Voltage: AC 100-240V
Plug: US Plug . EU Plug.UK Plug.AU Plug.Korea Plug etc
Number of Glue Sticks: 2 (Length 100 cm)
Suitable for bonding wood, metal, glass, fabric, plastic, ceramics and card.
The heater component of the product is made of positive temperature Coefficient electric resistance (PTC). It is heating very fast and automatic of control temperature.
The Hot Melt Glue Gun can use normally in 100V to 240V power supply. be free from the electric voltage motion to limit, inside place the fuse, use more safe.
This series product can be use the diameter from 10.8 mm to 11.5 mm of the melt glue.
Insert the gum from the glue gun tail, sent to the glue gun tube, put on the power supply to preheating from 3 to 5 minutes. button up to move the trigger and can extrude the melt glue, and can control the melt glue quantity.
1 x Hot Melt Glue Gun
2 x Glue Sticks
60-100W Hot Melt Hand Gun Specification:
|Input:||110-250V, AC, 60-100 W||Flow rate of glue:||16-18 g/min|
|Diameter of glue stick:||10.8~11.5 mm||Length of glue stick:||70~300 mm|
|Application temperature:||130~290℃||Product weight:||270g|
|Nozzel diameter:||2.0~2.3 mm||Pre-heating time:||3-5 mins|
|Inner box:||10 pcs||Outer ctn:||40 pcs|
| Inner box size: ||42x28x16 cm||Outer ctn size:||57x43.5x34 cm|
|G.W.:||14 kgs||N.W.:||10.8 kgs|
60-100W Hot Melt Hand Gun Show:
60-100W Hot Melt Hand Gun General SafetyInformation:
1. Checkif the plug cord was in good condition, and if there is stand before plug intothe electrical outlet ; Check if the used glue gun has glue flow through backof the tunnel;
2. wait5-10 minutes to allow glue to soften, stand up the glue gun on the table whennot in use;
3. Touchnozzle to any clean, dry surface you wish to bond, to avoid any impurity stopthe nozzle;
4. If the glue could not flow from the nozzle whenthe glue gun start to work, check if the glue gun are heating;
If gluegun can not be heated, there are following reasons:
1 Plug cord into electrical outlet notproperly;
2 Glue gun has been destroyed owing to innercord short circuit;
If gluegun can be heated, there are following reasons: Nozzle has been stopped by anyimpurity, ask careerman to manage it.
5. Do not use the glue gununder moist climate, humidity will affect insulation and cause electric shock;
6. Do not touch the nozzleor melted glue;
7. Do not remove out the melted glue stick fromthe tunnel back side, it will damaged the glue gun as well as scalding personhands.
8. Do not to disassemble or assemble any gluegun accessories freely, it will cause glue gun do not work properly;
9. Keep out of reach of children and stocked itbeyond any of Children palpable side;
10. Only used for melting glue stick, no otherusage;
11. When in use, there are any glue flow backfrom tunnel, stop using immediately, wait for careerman clean the glue;
12. Close the power if the glue gun not in useafter 15 minutes;
60-100W Hot Melt Hand Gun Using methods
1. Glue gunusing voltage is 110-220V AC,50/60Hz;
2. Tip gunforward on stand and place a piece of cardboard under the nozzle
3. Use 7-8mm(mini trigger glue gun), 11-12(big trigger glue gun), insert glue sticksthrough
tunnel at back of gun
4. After power,wait for 5-10 minutes to allow glue to soften
5. After gluesoftens, squeeze trigger to feed glue through glue barrel. Excessive force willdamage glue gun. Put down nozzle after work, disconnect the power plug.
Copyright © 2018 Ningbo Kingvos Electrical Appliance Co.,Ltd All rights reserved.